motec

Part No: #61304

OVERVIEW

MoTeC's LTC NTK (Lambda to CAN module) monitors, controls and diagnoses an NTK Lambda sensor, transmitting Lambda readings on a CAN bus.

When using multiple LTC NTKs, up to 32 Lambda sensors can be configured on a single CAN bus for simultaneous monitoring by an ECU or logging device.

FEATURES

Provides accurate Lambda measurement, even when exhaust gas temperature is changing rapidly (heating or cooling).
Calibrated by the user for a particular sensor using the initial sensor factory calibration, the free air calibration or the referenced gas calibration.
Pre-configured to suit a single unit installation. If necessary, the configuration can be adjusted; see the Configuration section for more details.
Units marked with a 2 or higher under the barcode are able to transmit extended Lambda values (Rich Lambda).

COMPATIBILITY

MoTeC ECU: M1 Series, M84, M400, M600, M800, M880

MoTeC Display/Loggers: All C Series Display Loggers, ACL, CDL3 (and discontinued models: SDL, SDL3, ADL, ADL2, ADL3)

PC COMMUNICATIONS

A MoTeC gateway device is required to communicate with the LTC on CAN. Such devices include:

M1 Series ECUs
All C Series Display Loggers, ACL, ADL3, SDL3, CDL3
UTC (USB to CAN) #61059

SPECIFICATIONS

Inputs/Outputs

1 x NTK Lambda sensor (MoTeC #57007)
Power supply voltage 11 V - 16 V
Power supply current 110 mA typical plus the sensor heater current. Heater current is typically 0.5 A - 1 A and up to 2 A on startup.

Communications

1 x CAN — using LTC Manager, configurable to:
125 Kbps, 250 Kbps, 500 Kbps or 1 Mbps

Physical

Dimensions: 38 x 26 x 14 mm, excluding wiring looms and connectors
Weight: 62 g
1 x 4 pin male DTM connector (power/CAN)
1 x mating connector for NTK Lambda sensor
Maximum ambient temperature: 100 °C

SOFTWARE

For multiple installations, LTC Manager software allows all units to be simultaneously managed and diagnosed.

The software is used to:

Configure and calibrate all units on the CAN bus
Display readings and diagnostics
Configure CAN transmission addresses
Control free air sensor calibration
Update unit firmware

CONFIGURATION

MoTeC LTCs come pre-configured to suit a single LTC unit installation. By default, the initial factory sensor calibration is used and the CAN address is 460.

It is only necessary to use LTC Manager if installing multiple LTC units, or if changes to the default settings are required.

DIMENSIONS AND MOUNTING

All dimensions in mm.

CONNECTOR PINOUTS

Connector A (and B for Dual version)

NTK sensor connector

Mating connector: supplied on sensor

Pin	Wire Colour	Description
1	Blue	Heater +
2	Yellow	Heater -
3	Orange	Rc
4	Black	Sensor 0 V
5	Not connected
6	Grey	Vs
7	White	Ip
8	Black	Sensor 0 V

Power / CAN Connector

DTM 4pin (M) (#68055)

Mating connector: DTM 4pin (F) #68054

Pin	Wire Colour	Description
1	Black	Battery -
2	Green	CAN Lo
3	White	CAN Hi
4	Red	Battery +

WIRING

To power the LTC, connect to either the ignition switch for fast sensor startup or the fuel pump relay to prevent accidental battery drainage.

Wiring example

For information on wiring a CAN bus with several LTCs and any number of other CAN devices (as per the example), refer to the relevant device manual.

PURCHASING

If you are interested in purchasing this product contact an Authorised MoTeC Dealer.

DOWNLOADS

User Manuals & Guides

Name

Version / Part

Published

Download

Name, Version / Part, Published

Name

Version / Part

Published

Download

LTC LTCD LTCN User Manual

Feb 2017

Download

LTC LTCD LTCN User Manual

Feb 2017

LTC LTCD LTCN User Manual

Feb 2017

Download

Useful Links

This page shows the relevant downloads for this product. For a full selection of MoTeCs downloads visit the Downloads page.

To keep up-to-date with the latest webinars or software you can subscribe to our mailing lists and we will send you a message when new items are released.

To sign-up for a mailing list click the "SIGN-UP: WEBINAR NEWS" or "SIGN-UP: SOFTWARE RELEASE" button below.