C12X Input Loom

Part No: #61259

This is a high quality, ready made loom that adds 6 analogue voltage inputs and 2 analogue temperature inputs to your C12X Race Terminated Loom, quickly and easily. The loom has been made so that it is simple to install, with minimal wiring required. Each of the eight 2 metre leads is individually twisted and heat shrunk for a professional finish.

To use this loom the optional C12X I/O Upgrade must be enabled.

C12X Race Terminated Loom

Part No: #62204

The C12X Race Terminated Loom provides convenient and easy connection of the C12X Race Logging Kit to your vehicle. It allows connection of the C12X to power, ethernet, ECU, GPS and buttons. Also, the loom has an Accessory lead that can be used to connect a MoTeC CAN based product, such as an LTC, Expander, V2, etc.

CAN ECU to Display Loom

Part No: #61198

This plug-in adaptor joins the C12X Race Terminated Loom (supplied in C12X Race Logging Kits) to the standard MoTeC CAN communications connector used by MoTeC M84, M400, M600 or M800 ECUs. It makes 70+ ECU channels available to the C12X.
This loom will also work with other manufacturers' CAN-based ECUs, with the exception that the round AMP connector must be removed and replaced with a suitable connection for the relevant ECU.

OBD-II to Display Loom

Part No: #61197

The OBD-II loom is a plug-in adaptor that connects the C12X Race Terminated Loom (supplied in C12X Race Logging Kits) to the standard, on-board diagnostics port of many modern vehicles.
This enables the C12X to display and log a selection of channels, which differs from car to car.
Vehicle compatibility will vary from region to region, but as a guide most cars built after 2007 have an OBD-II connector.

Two Button Loom

Part No: #61221

• Pre-wired with a terminated, plug-in loom
• Can be mounted in the steering wheel using the optional Curly Cord
• Curly Cord also provides the flexibility to add extra buttons

RS232 ECU to Display Loom

Part No: #61199

The RS232 ECU loom joins the C12X Race Terminated Loom (supplied in the C12X Race Logging Kits) to the D9 RS232 communications connector used by MoTeC M4, M48 or M8 ECUs.
This loom will also allow connection to many other RS232-based aftermarket ECUs; custom communication templates may be required.
The RS232 ECU loom can provide 40+ ECU channels to the C12X.

Toyota FT86 M150 Adaptor Loom

Part No: #61264

This loom works for both left and right hand drive, Toyota 86, Subaru BRZ and Scion FR-S.

Toyota Yaris GR 2020 Diff Loom

Part No: #61466

This loom is intended to be used with MoTeC's M142 TOYOTA YARIS GR 2020 KIT (#11412 ).

Curly Cord

Part No: #61222

Our plug-in curly cord allows the C12X Race Logging Kit buttons to be moved onto the steering wheel with ease. The loom is pre-terminated with a 6 pin DTM, and has 6 straight through wires, allowing for additional buttons if required.

CDL3 Loom

Part No: #62203

The CDL3 Race Loom enables quick, convenient installation of the CDL3 Track Kit to your vehicle, providing plug-in connection of the CDL3 Dash Logger to power, ethernet, ECU, GPS and buttons. In addition, the loom has an Accessory lead that can be used to connect a MoTeC CAN based product, such as an LTC (Lambda to CAN module), Expander or Video Capture System.

Connector A = 34W Key 2
Connector B = 26W Key 3
Connector C = 34W Key 1
Connector D = 26W Key 1

Connector A = 34W Key 1
Connector B = 26W Key 1

Connector A = 34W Key 2
Connector B = 26W Key 3

M1 Adaptor 150mm 34W Key 2 Stub Loom

Part No: #61254

Stub Only

M1 Adaptor 200mm 34W Key 2 Stub Loom

Part No: #61250

Stub Only

M1 Adaptor 250mm 34W Key 2 Stub Loom

Part No: #61407

Stub Only

M1 Adaptor 400mm 34W Key 2 Stub Loom

Part No: #61411

Stub Only

M1 Adaptor 80mm 26W Key 3 Stub Loom

Part No: #61474

Stub Only

M1 Adaptor 120mm 26W Key 3 Stub Loom

Part No: #61251

Stub Only

M1 Adaptor 150mm 26W Key 3 Stub Loom

Part No: #61255

Stub Only

M1 Adaptor 250mm 26W Key 3 Stub Loom

Part No: #61405

Stub Only

M1 Adaptor 400mm 26W Key 3 Stub Loom

Part No: #61409

Stub Only

M1 Adaptor 120mm 34W Key 1 Stub Loom

Part No: #61252

Stub Only

M1 Adaptor 150mm 34W Key 1 Stub Loom

Part No: #61475

Stub Only

M1 Adaptor 200mm 34W Key 1 Stub Loom

Part No: #61256

Stub Only

M1 Adaptor 250mm 34W Key 1 Stub Loom

Part No: #61406

Stub Only

M1 Adaptor 400mm 34W Key 1 Stub Loom

Part No: #61410

Stub Only

M1 Adaptor 80mm 26W Key 1 Stub Loom

Part No: #61476

Includes Ethernet #61131 2m

M1 Adaptor 200mm 26W Key 1 Stub Loom

Part No: #61253

Includes Ethernet #61131 2m

M1 Adaptor 250mm 26W Key 1 Stub Loom

Part No: #61404

Includes Ethernet #61131 2m

M1 Adaptor 400mm 26W Key 1 Stub Loom

Part No: #61408

Includes Ethernet #61236 1.8m

Mercury Racing M1 Connector D Stub Loom

Part No: #61445

Stub only fully sealed 180mm 26W Key 1 - Includes Ethernet #61429 0.5m

Mercury Racing M1 Connector C Stub Loom

Part No: #61444

Stub only fully sealed 220mm 34W Key 1

Mercury Racing M1 Connector B Stub Loom

Part No: #61443

Stub only fully sealed 300mm 26W Key 3

Mercury Racing M1 Connector A Stub Loom

Part No: #61442

Stub only fully sealed 350mm 34W Key 2

M400, M600, M800, M84 Cut-to-Fit Loom

(2.5m unterminated)

Part No: #61017

C18X Cut-to-Fit Loom

(3m unterminated)

Part No: #62206

M130 Cut-to-Fit Loom

(2.5m unterminated)

Part No: #62207

Also suits M150, M141, M142 (C&D connection), use in conjunction with a bespoke loom incorporating connectors #65067 and #65068.

CDL3 Input Output Loom

Part No: #61196